Biofield shaping is basically a pure harmonization of the organism. In other words, as a rule, nothing is changed in the interference zone, but the body is provided with the corresponding balancing frequencies.

The basis for understanding this type of room harmonization is provided by bioresonance. Paul Schmidt has already recognized and scientifically described at the beginning of the 70s that everything around us, as well as especially in ourselves, vibrates in very specific frequencies. Each frequency has both polarities, plus and minus. If there is an imbalance in one of the frequency values, i.e. a polarity shift, disharmony arises and later usually illness.

For example, if a person stays on an irritation zone - e.g. caused by a water vein - the polarity shifts on one or more certain frequencies and the body is weakened. If one knows the corresponding frequency values, one can make them available to the body in the room with the help of special resonators or as pure information. The most famous biofield shapers are supplied by the Rayonex company, whose founder was Paul Schmidt himself.

The approach of the Duplex series is to provide the full frequency spectrum of geopathic interference zones in both polarities in the room. Due to the law of resonance, the body uses only what it needs. In other words, if there is a deficit of a plus polarity in a certain frequency, it gets it directly, or it can help itself to it. With FM biofield shaping, BIOGETA® FM biofield shapers even manage to balance the body in polarities - in the case of earth radiation and electrosmog pollution - as well as to measurably eliminate the spectrum of geopathic interference zones.

In addition to the specific regulation level of FM Biofeldformers, the main focus in the development of the Mudule was on the energy factor.

What is the use of a system that instructs the body to feel certain radiation fields differently, or even of a system that manages to counteract an interference zone by means of individually adaptable counter-vibrations, if the energy value, very well definable by the Bovis value, remains in a range that vibrates lower than the human being?

Due to the law of negative entropy, the human being loses vital energy on such fields. That is, regardless of the harmful radiation spectrum, above all, the energy value of the place must be raised to at least a neutral value, otherwise important regulatory processes in the body can no longer take place. ...

If a mains isolation switch or mains decoupler is active, the BioFieldformer should not be plugged into the enabled bedroom.

In such cases, a bio-wafer or a biofield repeater is very well suited as a supplement. This would then ensure local elimination of the interference zones under the respective beds, while the FM Biofeldformer provides compensation at a central location during the day.

However, a part of the compensating frequencies also arrives in the sleeping areas despite the mains decoupler. And this is through lines in the neighboring rooms or rooms below.

In some cases, this is even sufficient for complete erasure of the interference zones even without bio-wafers during the night.

The modules do not consume anything. The silicon core oscillates the information through a membrane onto a conductor and thus onto the house current.

The energy required by the module is the natural vibrational property of the crystalline core.

It is quasi free energy, because it provides for the oscillation of the nucleus. Basically, every crystal - thus also silicon - vibrates by free cosmic energy.

Basically, there are two ways to build such modules. The first possibility - without going into detail - would be that certain information is stored on a carrier, in this case the silicon core of the module, and then released to the environment.

The second possibility is to install only an instruction on the core, after which a certain field generates itself again and again. This is comparable to a vector path, where start and end points are defined, and the distance in between is built up again and again. This allows vectors to be scaled arbitrarily without losing quality, whereas a bitmap, for example, consists of pixel points that quickly become blurred when zoomed in.

Compared to the FM biofield formers, these are constructed like a vector. This means that as long as the core can oscillate, a constant field will build up again and again without losing quality.

If you ever feel that the power has dropped, unplug the module and walk around the house with it for a few minutes. This will cause the core to resonate again and release the full frequency spectrum.

However, by using the mains decoupler that matches the modules, this is no longer necessary and the module remains permanently in oscillation.

The basis of the modules is silicon. It is virtually a microchip with a small rasp.

Silicon has a crystalline structure and is able to store the finest information and instructions and implement them accordingly. That is why silicon is used in the computer industry, and why quartz crystals serve as clocks in watches, for example.

The advantage of a silicon critsall is its oscillation property. It is therefore the perfect transmitter to resonate the regulation information onto the circuit.

A question that is asked very often, concerns the thickness of the modules. It is important to understand that the recommended size of the modules depends on the size distribution of the circuit and the resistors in it (branches, fuses, etc.).

It is not that a larger module produces "more energy", but has more volume, and vibrates more strongly. But it is the same information structure. The goal is to delete the existing interference zones through an interference, to balance the body in the polarities and and to raise "negative" Bovis values to the ambient level.

So it is possible to use an L size module in a small apartment without any problems. In case of doubt, we always advise to take the larger module instead of the smaller one.

As a rule, it is often the case that at the latest 4 weeks after a Biogate module has been put into operation, there is no longer any evidence of exposure to water vein faults, earth grids or NF electrosmog as well as HF electrosmog in the body.

However, this does not necessarily mean that all the symptoms that have arisen up to that point have disappeared directly. This usually takes a little longer.

The FM Biofeldformer balances polarities and "negative" areas of vibration so that we no longer lose energy, our cells do not depolarize and the autonomic nervous system is balanced.

The new series of modules works very gently, so you will probably notice only after a few days that you would like to stay in bed longer and overall rest.

In the first few days there may even be some restlessness, as the body often has to get used to the changed vibrational field first.

YES! The main efficiency of an FM biofield former is within the meter circuit of the corresponding dwelling. Experience has shown that the meter is too great a resistance for the information to be transferred across it to the rest of the house current.

However, if you have direct neighbors, they may also be able to benefit from your balancing vibration field through the cables laid in your walls. The same applies to apartments above.

However, by far not the same effect can be expected as if the module is active directly within the housing circuit.

Basically, it does not matter where the module is plugged in, because the regulation information is modulated on the 50Hz of the house current and thus distributed everywhere in the house / apartment.

Experience shows that the best results can be achieved if the module is plugged in on the same floor as the bedrooms or living room.

We recommend plugging it directly into a free wall socket and only into a multiple socket in an emergency.

In order to calculate the correct size, it is important to understand how the biofield shaper works. It modulates a packet of information onto the 50Hz of the power grid and thus distributes throughout the house - or within the meter circuit. This means that not only the inhabited rooms, but also other rooms where wires are installed must be added to the area. E.g. basement rooms, garages, carports and/or the attic. For the latter, it is usually sufficient to calculate 1/3 of the total area of the attic, because usually only one pipe goes up there. The same is true for most garages. However, if the attic is developed, it must be included with full floor space.